Hey guys, today I'm going to show you how to make a heater that not only lasts for hours or days, or even weeks, this heater can last for months. It can consistently put out heat. It is super simple to put together and it actually pushes air throughout the room. So this could be something for a long-term emergency or even long-term heating. It only requires a few simple things and there's a lot of different fuel sources and alternatives you can use. You're not just stuck with the one thing I'm showing you today. I'm going to show you some additional as well. But this good heater room literally during a power outage for an extended period of time. So let me show you how simple this is to put together and you'll be amazed at the overall results. Now this particular pipe is really inexpensive. It's made from aluminum and it's really just dryer vent, but you don't have to worry about it overheating because aluminum can take a massive amount of heat. But one of the great things about these elbows is you can direct the heat. You can set this heater up and then direct the heat to another area. So it's not just going to go straight up. So it just depends on where you're trying to direct your heat to. It's I guess you could call this a self-powered forced air heater. So I guess that's what I'm calling this. But anyways, this is really easy. Let's get started on doing the first step on this little forced air heater. Now the first thing I want to do is I want to make this a free-standing heater. So what I need to do, find out where this has been put together, so I don't want to drill any holes close to that. I'm going to go to the opposite side and I'm going to drill one hole here and one hole here because our legs need to come out a little bit of an angle so they can provide a little bit of support. I just found some of these little threaded rods and you can use anything you want to for support, but I think these work great because you can use this bolt to adjust the height of it. So you're not just stuck with one different, one single type of heating. So we're going to put that in there, we're going to put the second washer in and we're going to have just an angle on these so there's a little bit of stability because if we had these straight up and down, it'd be more likely to tip over. So we want these kind of at that type of angle and so I'm going to spread the holes out. The type of drill bit I'm using for this is a step drill bit. Not putting too much pressure because this metal is really thin. So just remember, we want these spread out and we're trying to angle them as steep of an angle as possible so we can have more stability in our pipe. Now we have our two holes drilled in one end, we need to do the same thing on the opposite end. Remember, not too close to the edge because you need to have a little bit of space for the piece that's going to be fitting inside of our pipe. So just remember that you want to make sure that you come off a couple of inches here if you are using this exact type of aluminum piping. Now you can use traditional stove piping. It's going to be a little bit more durable. This is a lot thinner. So just remember that you can use whatever you feel comfortable using as long as it's a metal that can tolerate some heat. Now the way we're going to assemble the legs on our heater here, we're going to put our threaded rod in. These are, like I said, adjustable so you can make it as tall as you want to or as closer to your fuel source. But I'm just going to make it maybe, maybe half an inch to the inside. Put your washer to the inside and then attach the nut. I'll try to get where you can see what's actually happening inside the pipe and then you can tighten this down and then you have a lot more stability. You don't have to worry about your legs moving. So you just tighten that down there and then you have it. And so we're going to do the same thing on the opposite side and create this more stable leg so we don't have to worry about it tipping over because the legs are so far spread so far apart. Okay, so I'm going to also add a thermometer to the exhaust side so we can get an idea of what type of air temperature we have exiting the pipe. So you have your air intake on the right, your air exhaust on the left. Normally I wouldn't even worry about the thermometer, I would just use my digital thermometer where I could just point and shoot the infrared thermometer I think it's called. So just remember that that's this is just an optional step, but I just want to be able to show them on video how the air heats up as the mini forced air heater runs through. This is a very simple device. Now you can adjust these to make it closer to your fuel source or further away. You can use longer threaded rods. You can even use something else to put it up underneath and attach it to something like a can. I'll show you that just a second because that idea came to me about raising it up even higher. So it really just depends on what you're using as a fuel source. But I'm going to show you one fuel source that can last over two months. Now as I mentioned just a second ago, you could use something as simple as a juice can like this. You don't have to worry get it, you don't have to worry so much about it getting overheated. Just remove the label and any glues that might be attached and then you can attach it to the bottom like that with some wiring, drill some holes in it. I'm going to use, I'm going to opt to use the legs that I've already created, but a couple of juice cans could raise it up and you don't have to worry about excessive heat. You can also, once you're finished with these, you can fill them with sand and then of course drill the holes in the sides and put a wire over it so it's more stable so you don't have to worry about it falling over. So you're not, if you don't have any threaded rods around your shop or around your house, just use something as simple as a juice can and just make sure it's wired and weigh this down so it doesn't fall over. Now my legs are spread out a little bit wider than I like them to be, so I'm going to wire them together, pull them together like that so they'll stand just a little bit higher because I need a little bit more space under here for the heating product. Okay, so by wiring the base of these together, I've pulled them in a little bit closer to each other so it's elevated a little bit higher off my surface. So as you can see, we have a little bit more room under here, there's a lot of stability and you can tighten up the bolts from the inside.