the charging board is in place. Now it's time to arrange the battery cells inside the case. Once I was happy with the layout, I trimmed off the original battery tabs. The next step was wiring all four batteries in parallel. That means connecting every positive terminal together and every negative terminal together. This keeps the voltage the same while increasing the overall battery capacity. After that, I connected the positive and negative outputs from the charging board directly to the battery pack. One thing I noticed was that the wires on the charging board were incredibly thin, so before going any further, I replaced them with a pair of thicker wires that should handle the current much more reliably. Once all the wiring was finished, I made sure to cover every solder joint with heat shrink tubing to prevent any accidental short circuits. As you can see, the charging board is working perfectly. It's even showing that the battery pack is sitting at around 70% charge. The next challenge was this messy wiring. I needed to keep every cable as low as possible so nothing would press against the back of the display. After a lot of rearranging and maybe a little bit of creative cable management, everything finally fit nice and neatly inside. With everything wired up, I wanted to check the battery pack's output voltage. Perfect, it's reading 3.9 volts, which is exactly what the phone needs. As you can see, the original phone battery operates at almost the same voltage. Alright, now it's time to modify the phone itself. I'll remove the back cover and power it directly instead of using the original battery. To do that, I'll use the phone's battery connector and solder the positive and negative leads from my battery pack directly to it. Next, I need to power the display controller. A USB type C power cable is connected directly to the positive and negative terminals of the battery pack. The original cable is for too long, so I'm replacing it with a much shorter one that can bend in any direction, making it much easier to route inside the enclosure. Finally, I'll secure the controller board in place using double-sided adhesive tape. Next, I'll mount the two speakers and connect all of the controller board cables to the controller board. With that done, every component inside my DIY tablet is finally in place. Now it's time of truth. Let's see if it powers on. No way, the display came to life instantly. That's a very good sign. But then I ran into a serious problem. The touchscreen had completely stopped working. What's strange is that I'd already tested it earlier, and the touch function worked perfectly. So something must have gone wrong along the way. Right now, the only way I can control the system is through the phone itself. I went through every setting in both Samsung Dex and the display's menu, hoping I'd miss something. Nothing. I also checked every cable connected to the controller board, and everything appeared to be plugged in correctly. At this point, I was completely out of ideas, but then after taking one more careful look, I spotted the most ridiculous mistake. I'd installed the touchscreen ribbon cable backwards. Seriously, it was such a simple mistake. The moment I flipped the cable and powered it back on, the touchscreen worked perfectly again. I couldn't believe that after all that troubleshooting, the problem was entirely my fault. Alright, to put the display back on this tablet carefully. Oh yeah, everything is finally together. After all the planning, cutting, wiring and troubleshooting, it's finally finished. Now it's time and enjoy the result of all that hard work. I think I can officially call this a tablet. So let's try a few everyday tasks and see how it performs. First, some simple web browsing and yeah, it's surprisingly smooth. The touchscreen is especially impressive. It feels responsive and every tap registers almost instantly. Next up is YouTube. The display is a 14-inch full HD panel, so while it's not the most stunning screen you'll ever see, it's more than everyday use. For someone like me, it's exactly what I need. One thing I wasn't particularly impressed with was the audio. In my opinion, the speakers don't sound all that great. Now for the real test, Minecraft. The render distance set to the lowest setting, this DIY tablet is pushing around 200 FPS. That's an incredible and that's not all. I can still take photos and record videos using the phone's camera, just like a normal tablet. When the battery gets low, I simply plug in the charger and keep using it. I can even adjust the display settings using the physical buttons on the side of the screen. It's a small feature, but it's surprisingly convenient. Shutting the tablet down is just all I have to do is exit Samsung Dex and press the phone's power button. That turns off both the phone and the display. To power it back on, just press the same button again. The only thing you need to do beforehand is disable the lock screen in the phone settings. So Dex starts up without asking for a password. And with that, I've successfully turned a broken phone into a fully functional tablet. It does everything I hoped it would and all the essential features work exactly as they should. The entire project cost me around $120. Honest.